pump body

This series are mainly gear , gear pump , valve, pump body, axial end seal.

主要有齿轮 、 轴 、 泵体 、 安全阀 、 轴端密封所组成.

Mainly by the impellers, pump body and pump cover composition.

主要由叶轮 、 泵体和泵盖组成.

The pump body, Vane wheel water distributor are made of stainless steel.

主机泵体, 叶轮分水器,外壳均采用不锈钢材质.

Is becoming a ground-source pump air-conditioning systems , the main body.

正逐渐成为地源热泵 空调系统 的的主体.

the design of boring fixture of high pressure oil pump body parts with column holes

高压油泵缸体柱塞孔镗削夹具的设计

Features: stainless steel material of the pump body. Stepless adjusting of the capacity in rated range.

特点: 泵体全部采用不锈钢材料, 包装量可在额定范围内无极调整.

information description for pump body parts in capp

泵体零件CAPP系统中的信息描述

According to the design of water pump body mechanics the smallest noise.

根据水力学原理设计的泵体,噪声最小.

The turning-body-over methods in parturients with indwelling epidural anesthesia pump after caesarean

剖宫产术后硬膜外留置镇痛泵产妇翻身方法探讨

If installs negative-pressure container on the syphon, in the condition of bottom valve leaking enables the water level in the syphon not fall, when start the pump, can leave out the procedure of pouring the pump body with water.

若在吸水管上加装负压吸水罐，可在底阀泄漏情况下，使吸水管内水位不下降，启动泵时可省去灌泵程序。

Aiming at the characteristics of structure and performance of pump body in high pressure gear pump, squeezing casting was employed to manufacture the pump body, and the optimized die structure parameters and processing parameters were provided.

针对高压齿轮泵前后泵体结构、性能要求等特点，研究了挤压铸造生产前后泵体的工艺过程，给出了最佳的模具结构参数和工艺参数。

This article introduces a series of special clamps for machining pump body of a Liquid Pump.

本文介绍了某种射流泵泵体加工的系列专用夹具.

Reverse Cycle Type: pump body mounted directly on the motor flange for easy vaporization of liquid.

逆循环型: 泵体直接装在电机法兰上,适用于易汽化液体.

If the pump is not charged, you are advised to fill the pump body by hand.

如果泵不起诉, 建议您以填补泵体的手.

machining technology for bq type oil jet pump body

BQ型喷油泵泵体加工工艺的研究

There is 2 CY gear pump series pump body, cover, gears, bearings and the shaft sealing etc.

2CY系列齿轮油泵是有泵体 、 泵盖 、 齿轮 、 轴承套以及轴端密封等零部件组成.

This utility model achieves cooling of the lip ring, increasing service life of the lip ring, thereby improving sealing effect of the pump body.

本实用新型实现对环形密封件的冷却，延长其寿命，从而提高泵体的密封效果。

The composing, function, selecting principle and key of parts of the pump, such as electromotor, axle-jointer, bearing box seat, water cooling seal cavity, down pump body, pump axle and impeller, are introduced in detail by pump body structure diagram.

给出泵体结构图，详细介绍泵的电机、联轴器、轴承箱座、水冷密封腔、下泵体、泵轴、叶轮等部件的组成、功能，各部件的选型原则和关键点。

Just make sure there is quantitative conduction liquid in the pump body before the operation.

管路中不需安装底阀,工作前只需保证泵体内储有定量引流液即可.

Under the condition of main body of boiler wasn't reformed, by upgrading the fire grate and the tail department being heated and fan facilities and water pump, the power upgrading of boiler was realized.

在不动锅炉本体的情况下，仅对炉排、尾部受热面、风机和水泵进行改造，从而实现锅炉的增容。

Compound Die Casting Technique for Vacuum Pump Body

真空泵泵体外壳复合金属型铸造工艺

Analyses that because of bottom valve leaking in a syphon of a centrifugal pump, water level in the syphon falls to below the vacuum value of permitting suction, causes that must fill the pump body and the syphon with water before starts the pump every tim;

分析了离心泵吸水管底阀泄漏，使管内水位下降至低于最大允许吸上真空值，致使每次启动泵前，必须往泵体和吸水管内灌满水才能启动泵；

One end of the pump body is provided with a detachable bottom board.

泵体一端装有可拆卸的底板。